What Does P.Con Mean On Kenwood Amp? Functions And Benefits
If you’re a car audio enthusiast, you’ve undoubtedly seen the letters “P.Con” on Kenwood amps and other vehicle audio equipment. But what does it mean on a Kenwood amp, and more importantly, what does it do?
It’s probably not something you want to mess with if you don’t know what it is. P.Con is short for Power Control, and it’s basically a switch that controls the amount of power that goes to your amplifier.
In this article, we’ll break down the meaning of P.Con and explain what it does for your car audio system.
What Does P Cont Mean On A Car Stereo?
Power control, or P.Cont is a wire found in most car stereo systems that allow you to control your amplifier’s power state remotely. It helps to send a signal to the amp to turn it on/off.
It can also be useful for remotely powering your amplifier on and off, saving you time and energy. In most cases, the P.Cont cable is simply blue, but some car stereo systems may have a blue/white cable instead. It indicates that the power control cord controls the amplifier.
It can be useful if you have an electric antenna, as it will allow you to switch it on and off without going to the car. If your vehicle has an electronic antenna, you can connect the P.Cont wire to receive a better signal. It will ensure that you can pick up stations without any issues.
It can also come in handy if you have a car with an aftermarket amplifier installed; by using P.Cont, you can easily turn the amplifier on and off without going under the hood.
The P.Cont wire is a useful addition to most car stereo systems. It allows you to remotely control your amplifier and antenna, saving time and energy. If you have an electronic antenna, be sure to connect the P.Cont cable to it to receive the best signal possible.
Read more:
What Does P.Con Value On A Kenwood Amp?
When installing a vehicle audio amplifier, it’s important to understand the different functions of the wiring. One such wire is the P.Con, so what does it mean on a Kenwood amp? It is the power control cord. This cable directs the amp to switch on and is typically attached to the blue or blue/white cable.
Basically, it works exactly the same as the P Cont on a normal car stereo. This wire transmits the signal to turn the amp on/off.
Connect it to your ignition’s “Run” button. Your amp will power on whenever the key reaches the run position.
On factory systems, they always tie up this cable with the ACC (accessory) source on your car. Doing so will keep the amp turned off while not using it, preserving your battery’s charge.
If you’re unsure where to find the ACC cable, consult your car’s owner’s manual or a professional installer. Once you’ve located it, connect the P.Con cable to it and tuck any excess wire away, so it doesn’t dangle or get in the way.
With the P.Con wire properly installed, your car audio amplifier will power on and off automatically whenever you start or turn off your car.
Frequently Asked Questions (FAQs)
What Is Rem Out On A Car Stereo?
When looking to connect an aftermarket car stereo, you may come across the term “REM OUT.” It is an abbreviation for “remote out,” referring to a special power cable on some stereos. When the radio receives power, the REM OUT cable activates the amplifier.
REM OUT wire is typically located on the back of the stereo unit. It is a blue wire behind the HU. This cord always links to the amp’s remote terminal.
If you do not have a REM OUT cable on your stereo, your amp will always be in working condition, even if you have turned off the vehicle engine.
While the REM OUT wire is not required for all aftermarket vehicle stereos, it can be a helpful feature if you are looking to install an amplifier in your vehicle. Using the REM OUT wire ensures that your amplifier is properly powered on and ready to use.
Where Does The Rem Wire Connect To?
The REM wire is responsible for the turn-on function of the amplifier. It is usually connected to the gauge fuse holder or the cable that supplies 12 volts to the accessory position on the ignition switch.
Connect the REM wire to the appropriate output if you use a head unit with remote turn-on capability. Failure to properly connect the REM wire may damage the amplifier or head unit. If you are unsure which output to use, consult your head unit’s owner’s manual.
Where Does The Remote Wire Go On A Car Stereo?
When installing a car stereo, the remote wire is one of the most important wires to connect. The remote cable is usually connected behind the stereo and is a blue or a blue/white wire. This cable allows the vehicle stereo to be turned on and off with the ignition.
There are two places to connect:
- Connect the remote cable to the positive battery terminal.
- Connect the remote cable to the ignition’s left side.
Read your vehicle stereo manual for more information. This connection is also very dangerous so you can ask for the help of specialists.
Read more:
Can I Connect Red And Yellow Wires Together?
No, it would be best if you did not connect the red and yellow wires together on a Kenwood amp. The red cable carries ignition, and the yellow cable carries constant power. When these two cables are connected, it will cause chaos in the head unit and drain the vehicle audio capacitor vs. battery.
Can I Use Speaker Wire For Remote Turn On?
It is possible to use a speaker wire for remote turn-on. When it comes to using a speaker cable for remote turn-on, there are a few things you need to keep in mind.
First, you must find some copper cable and ensure it is in good condition. Next, you’ll need to link the remote cord from your other amplifier to the speaker cable. Finally, make sure the connections are secure and will not come loose.
Ensure you connect the positive and negative cables correctly, or you could damage your amp or speakers.
Watch the video to learn more informative:
Conclusion
We hope this article has helped you understand what P.Con values are on a Kenwood amp and how to fix the issue if it is causing problems with your audio equipment. We wish you all the best in your endeavors, and thank you for reading! If you have any further questions, please don’t hesitate to leave a comment below or contact us directly.
Related posts:
