How To Reset Kenwood Car Stereo? Ultimate Guides For Newbies
Kenwood car stereo is a device that allows you to choose from stereo systems. Kenwood is a great brand that offers powerful stereo systems. Therefore, its products are always on the list of good car stereos. Although it is a powerful sound system, sometimes you need to factory reset it. You may have problems when asking to reset the Kenwood car radio. Especially if you are new, you will have more obstacles. Realizing the problem, I decided to share the article to guide you. Let’s read the manual for instructions on what to do to reset Kenwood car stereo!
When To Reset The Stereo?
Before learning what to do to reset the Kenwood car radio, you need to determine when to reset the stereo?
When you have used the radio for some time, the status of the stereo starting to work will appear. At the same time, the buttons may stop working for unknown reasons. Furthermore, the display may appear frozen or unresponsive.
These conditions will make you feel uncomfortable. You need to do some work to restore all to a simple setup state.
If you still find them difficult to use, try a factory method. If you want to know the exact problem with the sound system, then go to the nearest electronics store for inspection and repair.
Setting again will erase all previous settings and show the basic settings again. That way, you can start customizing your stereo.
How To Reset Kenwood Car Stereo?
Here’s how to reset Kenwood car radio. Note that they are all basic steps, so you should try to apply them correctly to get good results.
For KDC Models
The first is the ideal method for KDC models
- Power up stereo
You need to start the car by inserting the key into the ignition and then pressing the main screen button to turn on the radio.
Until a stereo light comes on, you have successfully turned on the power. Remember that this is an important step; if you do not supply power to the car radio, it will not be possible to initiate the reset.
- Get The Faceplate Off
Next, you’ll see the Faceplate off button on your stereo device’s tone. Click the button to remove the visor successfully.
Usually, it is in the bottom left corner of the radio. When performing these operations, you need to be very gentle when removing the visor.
Never shake or tug on the projection, as such strong impacts can damage or permanently damage the point.
- Press “reset”
Once you’ve done that, look for the little button on your radio system.
This switch is relatively small; it is difficult for the fingertips to reach it effectively, so find a pointed tool.
When you have the pointed tool ready, just put it on the reset button and hold it for a certain time. You just need to keep it for about ̀5 seconds, then retrieve the little tool to get the job done.
You will see the radio system reset at this point on display. All you need to do is keep waiting until the method completes.
For Touch Screen Stereo
The next method will help you set the models on the touch screen. When applied, you find two types, including soft and factory reset.
Right now, we will go into detail about each type of procedure.
Soft Reset
- A soft reset is applied when you get no response from the radio. Even when you have executed the commands or the device displays a message of minor problems.
- Like the method for KDC models mentioned above, you first need to locate the reset button and hold it to boot.
In this case, the reset button is small and lit up the triangle on your audio device, so identifying it shouldn’t be too difficult as it’s quite prominent. You can also find it in the top left corner of the radio.
- Once you have located the button correctly, you need to hold it for 5 seconds to put the device into the process. It’s worth noting that the soft reset method will retain all your custom settings.
Factory Reset
It is a factory reset method that also erases your previous custom settings.
In other words, when the operation is complete, your radio equipment will return to the way it was when it was new with its original production settings.
It’s a difficult method to do, so it’s best to find a friend to help.
- Press Eject CD
You will first find the Eject CD button to the left of the CD slot.
Once you have determined the correct location, you need to press and hold the two buttons simultaneously, the Eject CD and the volume button.
This operation is not too difficult, and you can do it yourself or ask more friends to complete it quickly.
- Hold “reset”
Next, you need to find the button in the top left corner of the radio device.
Still similar to the above methods, you need to hold it for a few seconds.
If you or a friend has down the volume and CD Eject volume, the other person can operate the set again button.
Keep holding the Eject CD button and the volume button until the stereo starts to boot up again to hold until the switch turns back on.
So your job is done, and you can get the radio working again.
- “Initialize All”
After successfully booting the system, you need to search for the initialize all button. It is set up on the display screen, and you can find it here and tap on it to start the process.
- “reset” again
Having completed the above steps, you need to do a full system set again.
Since the button is small, you can find a sharp object to press on the small triangular set again button to start the stereo.
Your device will revert to its original sound settings when it’s done, just like when it was new.
For Radio Bluetooth
Similar to the above methods, here you only need to follow two basic steps:
- Step 1: Remove the glass from the car stereo
- Step 2: Find the button on the front panel and use a sharp object to hold it down.
FAQs
1. Why is my Kenwood radio not working?
There are many reasons why the Kenwood car stereo is not displayed or not working.
You should first check the fuse located on the back of the radio. If a blown a fuse is found, replace it with a new product of equivalent amperage.
Also, the error may be in the power button. If you have turned on the ignition, but the Kenwood Car Stereo still does not display a message on the screen, then the power button is most likely faulty.
To test, you need to hold down the different buttons to see if the controls work properly. If only the power button does not work, bring the device to a specialized store for advice and repair.
2. Why am I not getting power to my stereo?
The cause of this problem may lie in the fuse. Test it to determine if it’s leaking. There are several other causes, such as short circuits or issues with the wiring.
In general, the environment in the car has a lot of influence on electronic equipment. All vibrations, heat, and dirt are all factors that cause them to fail.
3. How do I reset my car radio after I change the battery?
First, you turn the ignition to the on position, but you do not turn on the machine in this step.
Next, turn on the radio by pressing the volume control button. This procedure lasts 10 seconds and then turns off the radio.
Finally, you need to hold down the power button for about 5 seconds and observe the screen.
4. Why does my Kenwood stereo keep resetting?
There are many reasons why Kenwood stereo keeps resetting. They are related to batteries, ignition problems, fuses, and wiring, maybe the radio is too hot etc.
Conclusion
Resetting the Kenwood car stereo is not necessarily the same between device models, but most follow the basic principles I mentioned. In some cases, you can refer to the information in the manual provided by the manufacturer.
You can easily implement the methods in this article effectively on many different sound systems.
Hopefully, the information in this article can help you achieve your desired goal.
If you have any related questions, do not hesitate to leave a comment or contact us directly via email to receive a full response.
Don’t forget to share it with as many friends or family as possible who might be struggling with their how-tos. It can be helpful to one of them.
Associated posts:
- How To Connect A Subwoofer To An Old Amplifier?
- How To Connect Subwoofer To Receiver Without Subwoofer Output?
- How To Convert Home Subwoofer To Car? Top Guides For Newbies
- How To Connect Subwoofer To Car Stereo Without Amp?
- How Many Amps Does A Car Stereo Draw? Here’s The Answer!
- How To Keep Radio On When Car Is Off? – Tips & Guides
- How To Clear Memory On Pioneer Radio? 3 Easy Steps
- How Many Watts Is Good For A Car Stereo? The Last Answer!